欧美成人午夜在线播放-成人午夜视频欧美-情欲毛片亚洲一区二区-日本亚洲欧美综合在线-欧美亚洲日本va

當混凝土攪拌車安裝完畢時，調試并不是一個缺失的過程，調試用戶可以放心使用，如何準確調試呢？

When the concrete mixer is installed, debugging is not a missing process, debugging users can rest assured to use, how to accurately debug it?

在調試控制系統時，重設應急按鈕，關閉電器柜中的電源，關閉各支路斷路器、控制回路電源開關、控制室電源開關，檢查電氣系統中是否存在異常現象，是否立即進行檢查。

When debugging the control system, reset the emergency button, turn off the power in the electrical cabinet, turn off the branch circuit breaker, control circuit power switch and control room power switch, and check whether there is any abnormal phenomenon in the electrical system and whether it is checked immediately.

打開每臺馬達的按鈕，試試馬達轉向是否準確，如果不準確，應立即調整。

Turn on the button of each motor to see if the motor steering is accurate. If not, adjust it immediately.
          

啟動混凝土攪拌車的空氣泵，等待空氣壓力達到要求，按按鈕標記啟動每扇氣體控制門，以確定是否動作靈敏。

Start the air pump of the concrete mixer, wait for the air pressure to meet the requirements, and press the button mark to start each gas control door to determine whether it is sensitive.

調整微機的零點和靈敏度，檢查空壓機的開關是否正常，氣壓表是否準確，調整安 全閥的壓力以規范刻度。

Adjust the zero point and sensitivity of the microcomputer, check whether the switch of the air compressor is normal, whether the barometer is accurate, and adjust the pressure of the safety valve to standardize the scale.

試試看攪拌車是否顯示出異常的噪音，以及每個部件是否能正常工作。

Try to see if the mixer shows abnormal noise, and whether each part can work properly.

在帶式輸送機的調試中，有必要進行工作，在運行過程中看每一輥的運行是否靈敏，要仔細檢查皮帶，不能有搖動、跑偏、磨磨、打滑、變形等情況。

In the commissioning of the belt conveyor, it is necessary to work, in the process of operation to see whether the operation of each roll is sensitive, to carefully check the belt, can not have shaking, deviation, grinding, slipping, deformation and so on.

在調試混凝土配料機時，必 須多按配料按鈕，看它是否靈敏，是否能準確安裝，然后在調試配料時參考。

When debugging the concrete batching machine, you must press the batching button to see if it is sensitive and can be installed accurately, and then refer to it when debugging the batching machine.