1.檢查自上料攪拌一體車的密封件是否有大的裂縫或裂縫。如果密封破裂，可用膠水修理。特別是，在密封件上使用特殊的粘合劑可以輕松填充較大的裂縫區域。當然，如果密封件嚴重損壞或損壞，請更換新的密封件。
1. Check whether there are large cracks or cracks on the seals of the self loading mixer. If the seal breaks, it can be repaired with glue. In particular, the use of a special adhesive on the seal can easily fill large crack areas. Of course, if the seal is seriously damaged or damaged, replace it with a new one.
2.在駕駛員使用混凝土混合清潔劑清潔門窗密封條之后，請涂一層防滲透劑，以防止密封條老化，并顯著提高密封條的密封性能。另外，密封條之間的間隙容易充滿灰塵和銹蝕。因此，您需要使用刷子灰塵。
2. After the driver uses the concrete mixed cleaner to clean the door and window sealing strip, please apply a layer of impermeable agent to prevent the sealing strip from aging and significantly improve the sealing performance of the sealing strip. In addition, the gap between sealing strips is easy to be filled with dust and rust. Therefore, you need to use a brush to remove dust.
3.更換整個車身時，有必要在焊縫的重疊部分涂一層密封劑。粘合劑層的厚度約為1mm，并且粘合劑層必須沒有不適當?shù)恼澈?，氣泡和其他缺陷。地板的整個底面和前輪蓋的底面應涂3毫米4毫米的彈性涂層和防腐涂層。這些措施不僅顯著提高了車身的密封性能，減緩了車身的腐蝕速度，而且大大提高了乘坐舒適性。
3. When replacing the whole body, it is necessary to apply a layer of sealant on the overlapping part of the weld. The thickness of the adhesive layer is about 1mm, and the adhesive layer must be free from improper bonding, bubbles and other defects. The entire underside of the floor and the underside of the front wheel cover shall be coated with 3mm to 4mm elastic coating and anti-corrosion coating. These measures not only significantly improve the sealing performance of the body, slow down the corrosion rate of the body, but also greatly improve the ride comfort.
4.密封門和車身是一個相對困難的部分。密封要求相對嚴格。要密封的部分相對較長，要密封的部分的橫截面形狀不同，并且門經常被打開和關閉。在自上料攪拌一體車上安裝三向密封和四向密封，并安裝前立柱的四密封結構和頂梁的側梁。這樣的多通道密封件通常被放置在前門的間隙中，并且除了密封功能之外，它們還具有減少車輛噪音的作用。
4. Sealing the door and body is a relatively difficult part. The sealing requirements are relatively strict. The part to be sealed is relatively long, the cross-sectional shape of the part to be sealed is different, and the door is often opened and closed. Install three-way seal and four-way seal on the self feeding and mixing integrated vehicle, and install the four-way seal structure of the front column and the side beam of the top beam. Such multi-channel seals are usually placed in the gap of the front door, and in addition to the sealing function, they also reduce vehicle noise.
5.車窗玻璃損壞后，螺絲刀應在更換玻璃時檢查密封條是否損壞。窗戶在維修后通常不能恢復其原始形狀，因此，除了能夠輕松地拉動和提起玻璃窗外，還應注意玻璃窗周圍的密封。如果玻璃和玻璃容器之間的間隙不均勻，則橡膠條將不容易與玻璃和玻璃容器接觸，并且駕駛員可以輕松地用手拉動密封環。
5. After the window glass is damaged, the screwdriver shall check whether the sealing strip is damaged when replacing the glass. Windows usually cannot be restored to their original shape after maintenance. Therefore, in addition to being able to easily pull and lift the glass window, attention should also be paid to the sealing around the glass window. If the gap between the glass and the glass container is uneven, the rubber strip will not easily contact the glass and the glass container, and the driver can easily pull the sealing ring by hand.
6.更換車頂時，駕駛員必須先壓裝并在車頂周圍涂上一層導電密封膠。焊接后，在流道和接頭上涂卷邊膠。這不僅對身體有幫助。密封件可以防止由于法蘭焊縫上積水而導致的汽車過早腐蝕。
6. When replacing the roof, the driver must first press fit and apply a layer of conductive sealant around the roof. After welding, apply crimping adhesive on the flow channel and joint. It's not just good for the body. The seal can prevent premature corrosion of the vehicle caused by water on the flange weld.
7.自上料攪拌一體車的天窗是大多數家用汽車的基本配置。當您打開汽車的天窗時，橡膠密封條會暴露在空氣中，這不可避免地會積聚灰塵，甚會進入小礫石中。長期使用后，天窗可能會因磨損而變形，排水孔可能會堵塞。因此，定期清潔叉車并潤滑叉車非常重要。
7. The skylight of the self loading mixer is the basic configuration of most household cars. When you open the sunroof of the car, the rubber sealing strip will be exposed to the air, which will inevitably accumulate dust and even enter the small gravel. After long-term use, the sunroof may be deformed due to wear and the drain hole may be blocked. Therefore, it is very important to clean and lubricate the forklift regularly.
點擊撥打服務熱線：4008791999
