欧美成人午夜在线播放-成人午夜视频欧美-情欲毛片亚洲一区二区-日本亚洲欧美综合在线-欧美亚洲日本va

自動上料攪拌車在夏天的使用可以說是一個考驗，畢竟夏季氣溫升高，混凝土更容易凝結，更容易造成攪拌機水溫過高。那么，攪拌機水溫偏高的原因除了高溫還有哪些呢？讓我們看看。

The use of automatic loading mixer in summer can be said to be a test. After all, with the temperature rising in summer, the concrete is easier to set, which is more likely to cause the mixer to have too high water temperature. So, what are the reasons for the high water temperature of the mixer besides high temperature? Let's see.

1、冷卻風扇不正常運轉時，攪拌機不容易出現水溫高的問題，但如果冷卻風扇出現問題，水溫容易升高。

1. When the cooling fan does not operate normally, the mixer is not prone to high water temperature, but if the cooling fan has problems, the water temperature is easy to rise.

2、如果溫控器損壞，很容易造成水溫過高。此時，需要更換恒溫器。更換方法：先拆下節溫器，堵住小循環，保證冷卻液全部被水箱散去；安裝新溫控器時，注意水孔。不行的話，用6mm鉆頭鉆一個，一個打標，一個打標，車輛加熱的時候，溫控器兩邊有溫差，可以讓溫控器隨著水溫準確開啟。

2. If the thermostat is damaged, it is easy to cause the water temperature to be too high. At this time, the thermostat needs to be replaced. Replacement method: first remove the thermostat, block the small circulation, and ensure that all the coolant is dispersed by the water tank; Pay attention to the water hole when installing a new thermostat. If not, use a 6mm drill bit to drill one, mark one, and mark the other. When the vehicle is heated, there is a temperature difference on both sides of the thermostat, which can enable the thermostat to open accurately with the water temperature.

3、水箱堵塞也會導致水溫升高。方法：外部堵塞物應用水或空氣；內部堵塞會影響冷卻液循環并產生壓力。這時候有兩個結果：一是水箱漏水，二是高速行駛時水溫特別高。

3. A blocked water tank can also cause the water temperature to rise. Solution: remove the external blockage with water or air; Internal blockage will affect the coolant circulation and generate pressure. At this time, there are two results: one is that the water tank leaks; the other is that the water temperature is particularly high when driving at high speed.

4、水泵出現故障的原因有二：一是自動上料攪拌車的葉輪打滑或卡死，造成皮帶斷裂；二是葉輪變形。

4. There are two reasons for the failure of the water pump: first, the impeller of the automatic feeding mixer slips or gets stuck, causing the belt to break; Second, the impeller is deformed.

5、氣缸損蝕。氣缸損蝕一般有四方面的原因：燃燒室與水道沖，這時會從排水管排水或排白煙，造成水箱經常性缺水；水道與油道沖（機油有水呈白色）；水道與水道沖，造成缸體散熱不良，尤其在高速時影響更大；水道堵塞也會引起氣缸損蝕。

5. Cylinder is corroded. There are generally four reasons for cylinder erosion: the combustion chamber and water channel are flushed, and at this time, water or white smoke will be discharged from the drain pipe, resulting in frequent water shortage in the water tank; Water channel and oil channel flushing (the oil is white with water); The water channel and water channel collide, resulting in poor heat dissipation of the cylinder block, especially at high speed; Clogged waterways can also cause cylinder erosion.

所以說夏天使用攪拌車工作時需要注意水溫高的問題，否則會對攪拌機造成不可逆轉的影響。更多關于該機器使用的內容就來關注我們網站www.fxsgujg.cn了解吧！

Therefore, attention should be paid to the problem of high water temperature when using the mixer in summer, otherwise it will have an irreversible impact on the mixer. For more information about the use of this machine, please pay attention to our website www.jfhntjbc Www. 68mn!