概述：保養對攪拌車的重要性都知道，那么怎樣保養才能確保我們的設備長久使用且不出問題呢？攪拌一體車廠家為您解說。
We all know the impor
保養對攪拌車的重要性都知道，那么怎樣保養才能確保我們的設備長久使用且不出問題呢？
攪拌一體車廠家為您解說。
We all know the importance of maintenance to the mixer truck, so how can we ensure that our equipment can be used for a long time without problems? The mixer manufacturer will explain to you.
1、檢查車輛發動機機油、柴油、轉向油、離合器油、制動油液及發動機冷卻液等的加注情況，確保車輛的正常使用，并及時更換和清理機油濾芯、柴油濾芯、空氣濾芯。
1. Check the filling of engine oil, diesel, steering oil, clutch oil, brake oil and engine coolant of the vehicle to ensure the normal use of the vehicle, and timely replace and clean the engine oil filter element, diesel filter element and air filter element.
2、檢查轉向系統、離合器、制動系統工作是否正常。檢查照明燈、報警器、轉向指示燈、剎車燈、雨刮器等動作是否正常,均應清潔。檢查輪胎氣壓是否正常,不應有破裂和損傷，輪胎螺母不得有松動。
2. Check whether the steering system, clutch and braking system work normally. Check whether the action of lights, alarms, direction indicators, brake lights, wipers, etc. is normal and should be cleaned. Check whether the tire pressure is normal, there should be no cracking and damage, and the tire nut should not be loose.
3、檢查完畢啟動車輛進行預熱，檢查機油壓力、發動機水溫是否正常，底盤氣路有無漏氣情況。
3. After inspection, start the vehicle for preheating, check whether the oil pressure and engine water temperature are normal, and whether the chassis air circuit has air leakage.
4、檢查帶有尿素的車輛，發動機熄火少30S以內不要關閉車輛總電源，此時系統會將管道殘余的尿素溶液排除，以避免結晶堵塞噴嘴。
4. Check the vehicle with urea. Do not turn off the main power supply of the vehicle within at least 30s after the engine is shut down. At this time, the system will discharge the residual urea solution in the pipeline to avoid crystallization blocking the nozzle.
5、檢查液壓泵、馬達、減速機是否有漏油現象，檢查液壓油、減速機齒輪油是否充足，有無變質，液壓油濾芯是否滿足使用要求，液壓油散熱器能否正常運行。6、檢查主、副車架連接螺栓是否松動、脫落；檢查副車架及底盤大梁是否有開裂現象。
5. Check whether the hydraulic pump, motor and reducer have oil leakage, whether the hydraulic oil and reducer gear oil are sufficient and deteriorated, whether the hydraulic oil filter element meets the use requirements, and whether the hydraulic oil radiator can operate normally. 6. Check whether the connecting bolts of the main and sub frames are loose and fall off; Check whether the subframe and chassis girder are cracked.
7、檢查滾道及托輪表面是否有異物，并及時；轉動攪拌筒，查看是否有抖動、異響等；查看托輪緊固螺栓是否松動，托輪是否移位；滾道、托輪表面、托輪內部涂抹潤滑脂。
7. Check whether there are foreign matters on the surface of the raceway and supporting wheel, and remove them in time; Rotate the mixing drum to check whether there is shaking, abnormal noise, etc; Check whether the fastening bolts of the supporting wheel are loose and whether the supporting wheel is displaced; Apply grease on the surface of the raceway, the supporting wheel and the inside of the supporting wheel.
8、檢查進料斗、溜槽處是否有結料并；檢查溜槽伸縮支撐旋轉時是否伸縮正常，并往伸縮支撐及支撐搖桿處加注潤滑脂。
8. Check whether there is material deposition at the feed hopper and chute and remove it; Check whether the expansion and contraction of the chute telescopic support is normal when rotating, and fill the telescopic support and the support rocker with grease.
9、檢查傳動軸連接螺栓是否松動，傳動軸花鍵及十字軸處加注潤滑脂。
9. Check whether the connecting bolts of the transmission shaft are loose, and add grease to the splines and cross shafts of the transmission shaft.
10、檢查轉動操縱手柄操縱是否卡滯，操縱各油嘴處加注潤滑脂。
10. Check whether the operation of turning the joystick is stuck, and fill grease at each oil nozzle.
The above are the precautions for the inspection and maintenance of the mixer truck before construction. I hope it can be helpful to you. For more relevant matters, please come to our website http://www.fxsgujg.cn Consult and have a look.
點擊撥打服務熱線：4008791999
