概述:自上料攪拌車有時候會出現問題,是由于里面有很多的土渣沒有清理干凈,需要及時將內部的土渣清理出來,這樣才能使它正常運行,接下來就教大
自上料攪拌車有時候會出現問題,是由于里面有很多的土渣沒有清理干凈,需要及時將內部的土渣清理出來,這樣才能使它正常運行,接下來就教大家清理土渣的方法,在此五種方式。
Sometimes there are problems with the self feeding mixer, because a lot of soil residues are not cleaned up, so it is necessary to clean up the internal soil residues in time, so that it can operate normally. Next, we will teach you how to clean up the soil residues, and here we recommend five methods.
一般來說對于攪拌機在使用時候我們都會提前檢查但是因?yàn)橥猎跀嚢铏C(jī)的內部平時不太注意,但是只要我們稍微仔細看下就能發現這種情況所以我們?cè)偈褂们岸伎梢韵葯z查這個問題把這種情況防患于未然。
Generally speaking, we will check the mixer in advance when it is used, but we don't pay much attention to the soil slag inside the mixer, but as long as we look carefully, we can find this situation, so we can check this problem before using it to prevent it.
1、準備好緊急驅動軟管,將自上料攪拌車熄火,卸下液壓馬達上的高壓油管接頭。
1. Prepare the emergency drive hose, turn off the self feeding mixer truck, and remove the high-pressure oil pipe connector on the hydraulic motor.
2、將救援車熄火,將其液壓馬達的高壓油管卸下,并與故障車上的對應接頭用緊急驅動軟管相連。
2. Turn off the rescue truck, remove the high-pressure oil pipe of its hydraulic motor, and connect it with the corresponding connector on the faulty truck with the emergency drive hose.
3、發動救援車,將其操縱手柄撥出料位置,故障車內的混凝土即被排出。
3. Start the rescue truck and turn its handle to the discharge position, and the concrete in the faulty truck will be discharged.
4、緊急驅動完畢后,將驅動軟管卸下,并恢復兩車原狀。
4. After the emergency drive is completed, remove the drive hose and restore the two vehicles to their original state.
5、還有一種簡單點的方法就是在托輪和滾道之間放入木楔,控制攪拌筒的旋轉,將發動機熄火,拆松液壓馬達的一根高壓油管,攪拌筒可自由旋轉,控制攪拌筒的旋轉,使維修孔轉到下部,然后打開維修孔,清理出筒內混凝土?;炷僚懦鐾戤吅?,恢復攪拌車原狀。
5. Another simple method is to put a wooden wedge between the supporting wheel and the raceway, control the rotation of the mixing cylinder, turn off the engine, loosen a high-pressure oil pipe of the hydraulic motor, the mixing cylinder can rotate freely, control the rotation of the mixing cylinder, turn the maintenance hole to the lower part, open the maintenance hole, and clean the concrete in the cylinder. After the concrete is discharged, the mixer truck shall be restored to its original state.
The above is the method of cleaning soil slag from the charging mixer truck. No matter which method you choose, you should pay attention to safety. More related use matters will come to our website http://www.fxsgujg.cn Consult!